Intellinet 24-Port Gigabit Ethernet Rackmount Managed Switch Manual de usuario Pagina 1

16/24-PORTGIGABIT ETHERNET RACKMOUNT MANAGED SWITCH USERMANUALMODEL 523547/523554 INT-523547/523554-UM-0107-01

To save the port configuration, click “Apply.” You can also click the “Refresh” button to see the current status of each port.VLAN ConfigurationVLAN div

11PVID: When the VLAN-enabled switch receives a tagged packet, the packet will be sent to the port’s default VLAN according to the PVID (port VLAN ID)

Aggregation/Trunk ConfigurationTo set up port trunk groups, click in the ports’ number columns on the desired Aggregation Group row (1–8) per the config

13Quality of Service ConfigurationQoS enhances communication quality by assigning precedence to classified packets. This switch has port-based, tag-base

2. Click “Tag priority” to display the Tag Priority Setting page.3. From the drop-down menu, select the port you are going to configure.4. Select “high

Rate Limit ConfigurationRate Limit manages the bandwidth for each port and presents the settings options for Storm Control, which limits the flow rates

To initiate Auto Search: 1. Click “Apply” to list the found devices. 2. Click the IP address hyperlink to access the device.To use Manual Add

RestartTo restart the system, click “Yes.” The system will restart and display the Authentication window. As before, enter the username and password t

Click on the property icon and select settings. Confirm the settings below. “The Function, arrow, and ctrl keys act as”: Terminal keys ”Emulation”: VT1

System Restore Default [keepIP] Description: Restore factory default configuration. [keepIP]: Preserve IP configuration (default: not preserved).UserNam

CONTENTS 1. Introduction ...3 Front Panel...

1000fdx: 1 Gbps, full duplex. auto: Auto negotiation of speed and duplex.Port Flow Control [<portlist>] [enable|disable] Description: Set or

21 VLAN Egress [<portlist>] [untagged|tagged] Description: Set or show the VLAN egress mode setting for the port. Egress untagged ports will s

22 QoS Port [<portlist>] [<class>] Description: Set or show the port class. In tag mode, the default class is used for untagged frames.

23 SNMP CommandsSNMP Configuration Description: Show the SNMP configuration.SNMP Community [<get>|<set>] [<community>] Description: Se

24 5. SPECIFICATIONS Standards• IEEE 802.3 (10Base-T Ethernet) • IEEE 802.3u (100Base-TX Fast Ethernet) • IEEE 802.3ab (Twisted Pair Gigabit Ether

25 Configuration Options• Full and half duplex per port • Port link speed: 10 Mbps, 100 Mbps, 1000 Mbps or auto-negotiation • Port bandwidth control

26 NOTES

27 NOTES

Are you completely satisfied with this product?Please contact your INTELLINET NETWORK SOLUTIONS™ dealer with comments or questions.Copyright © INTELLIN

1. INTRODUCTION Thank you for purchasing this INTELLINET NETWORK SOLUTIONS™ Gigabit Ethernet Rackmount Managed Switch, Model 523547 (16-port) or Mode

FRONT PANELPorts and LED indicators are found on the front panel of the switch. The tables below explain their purpose and operation. LEDsNOTE: The fo

Restore Default ButtonUse this button to reset the switch or restore factory default settings. To reset, press the button once. To restore factory def

NETWORK CABLE INSTALLATIONCrossover/Straight-Through CableAll the ports on the Gigabit Ethernet Rackmount Managed Switch support Auto-MDI/MDI-X funct

incoming packets to VLANs according to their ingress port. The 802.1Q-based VLAN adds a tag to the header of the packet to classify the VLANs.Trunk (A

System ConfigurationThe System Configuration window presents the switch information and allows the configuration of the switch properties. MAC Address: T

Port ConfigurationThe Port Configuration page shows the link status of each port and allows the configuration of speed, flow control and maximum frame siz